Yaqin:NEWS
Location: Home > Company news > Yaqin speaker tells you how to prolong the service life of the tube amplifier

Yaqin speaker tells you how to prolong the service life of the tube amplifier

release time: 2021.04.22
Summary: 
In use, the electron tube should have good ventilation and heat dissipation, the overheating temperature will shorten the life of the electron tube, so it is necessary to keep the electron tube at a lower temperature as far as possible.

In use, the electron tube should have good ventilation and heat dissipation, the overheating temperature will shorten the life of the electron tube, so it is necessary to keep the electron tube at a lower temperature as far as possible. 

In use, the electron tube should have good ventilation and heat dissipation, the overheating temperature will shorten the life of the electron tube, so it is necessary to keep the electron tube at a lower temperature as far as possible.

The electronic tube is afraid of vibration, so it is also very important to take anti vibration measures to avoid vibration as far as possible. If these two points are achieved, the service life of the electron tube can be at least doubled. For this reason, there should be proper space around the electron tube equipment, especially above it, so as to have good convective ventilation. If possible, fans can be used to help heat dissipation.


The cathode of electron tube will be damaged before it reaches the required temperature, that is, when high voltage power supply is added, and the life of electron tube will be shortened. Therefore, if the electronic tube equipment has a preheating device, it must be used. For example, turn on the filament low-voltage power supply for preheating, and then turn on the high-voltage power supply. If there is no preheating device, do not rush to connect the input signal, turn off the volume to the minimum, and wait for 20-30 minutes to warm the machine before using it. If the side heating rectifier is used to supply the whole machine with high voltage, it just provides a simple and effective high voltage delay. In addition, in normal use, do not switch the power supply frequently.


Of course, if the electronic tube circuit is correctly designed and misused, the electronic tube will not die prematurely. It should be normal for the electronic tube to use thousands of listening hours. The most common errors in the circuit design are too high potential difference between the filament and cathode of the electron tube, the maximum voltage of the screen or curtain grid of the electron tube, too low or too high filament voltage of the electron tube, overheating of the electrode caused by improper installation position of the electron tube and no delay device for the high voltage power supply


            

Hot product recommendation 

MS-90B

MS-90B

Output Power:UL55W×2(8Ω)   TL28W×2(8Ω) Frequency Response:5Hz--70KHz(-2dB) Distortion:≤0.8% SNR:≥90dB(A) Input Sensitivity:Intergrated:≤250mV  Maximum Power Consumption:≤390VA Tube:KT88-EH x 4  6N8P  or 6SN7 x 4     12AX7 /ECC83x 2
MS-77T

MS-77T

Output power: 40W + 40W (8Ω) Distortion: ≤0.5% (1KHz) Frequency response: 5Hz -68kHz Signal-to-noise ratio: ≥88dB (A weighting) Input sensitivity: ≤0.23V (1KHz) Electronic tube: 7027B × 4 6J1 × 8 Load impedance: 4Ω-8Ω Power consumption: about 250W
MS-34D

MS-34D

Output Power:32W×2(8Ω) Frequency Response:10Hz--70KHz(-2dB) Input Sensitivity:Intergrated:≤300mV Maximum Power Consumption:≤250W Tube:EL34 x 4  12AU7 x 2          12AX7 x 1  6Z4 x 1 Gross Weight:about 25.5 kg Net Weight:about 23 kg Size:(W)400mm(D)355mm(H)220mm
MS-34B

MS-34B

Output Power:UL38W×2(8Ω) Frequency Response:10Hz--48KHz(-2dB) Distortion:≤1.0% SNR:≥90dB(A) Input Sensitivity:Intergrated:≤260mV Maximum Power Consumption:≤250W Tube:EL34 x 4  6N8P x 2 6N9P x 1   Gross Weight:about 25.5 kg Size:(W)400mm(D)355mm(H)220mm
MS-20B

MS-20B

Output Power: 25W+25W (8Ω) three-pole (TR) connection    50W+50W (8Ω) ultra-linear (UL)  connection Frequency response: 5Hz-80KHz (-2dB)  Distortion: ≤0.5% (at 35W)  Signal to noise ratio: ≥91dB (A) Input sensitivity: combined type&nbs
MC-100B

MC-100B

Output Power: 25W+25W (8Ω) three-pole (TR) connection    50W+50W (8Ω) ultra-linear (UL)  connection Frequency response: 5Hz-80KHz (-2dB)  Distortion: ≤0.5% (at 35W)  Signal to noise ratio: ≥91dB (A) Input sensitivity: combined type ≤ 0.25V Maximum power consumption: ≤370W  Electronic tube: KT88×4 6N8P×4 12AX7B×2  Gross weight: about 31 kg
  MS-84L

  MS-84L

Output power: 2x12W (4Ω-8Ω)  Harmonic distortion: ≤2%  Signal to noise ratio: ≥80db (A)  Frequency response: 6HZ-90KHz  Input sensitivity: 250mV  Input signal level: ≤300mv  Maximum power consumption: ≤90W  Tube: 6P14*4 12AX7B*2
MC-13S

MC-13S

Output power: 40W + 40W (8Ω)  Distortion: ≤0.9%(28W)  Frequency response: 10Hz -76KHz (-2dB)  Signal to noise ratio: ≥85dB (A weighting)  Power consumption: ≤220W  Sensitivity: ≤0.26V  Electronic tube: EL34×4 or 6CA7T×4 12AT7×4  Gross weight: 22Kg  Volume: length 470mm × width 315mm × height 175mm

Contact Yaqin

  • mobile phone:0757-81102208
  • QQ:3607877004
  • mailbox:3607877004@qq.com
  • address:6th floor, No.4 Badou Road, Lijia Industrial Zone, Shang'an, Danzao Town, Nanhai District, Foshan City, Guangdong Province
二维码
二维码

二维码

咨询热线
0757-81102208
网站首页
返回顶部